ADHESION PU40 is a one-part, non-sag, polyurethane sealant. Once extruded, it cures by reaction to the atmospheric moisture to form a high performance, dual purpose adhesive and sealing compound with permanent elasticity.
Pre-test substrates for adhesion. Cleaners and/or primers may be required to achieve optimal adhesion. As a rule, the substrates must be prepared in accordance with the NPT instructions; technical guidance regarding adhesion on specific surfaces may be obtained by submitting substrate samples for analysis to our laboratories. Surfaces must be clean, dry, free of water, oil, grease or rust and of sound quality. Remove all loose particles or residues with a jet of compressed air, sandpaper or hard brush. Glass, metal and other non-porous surfaces must be free of any coatings and wiped clean with solvent. Pre-cast panels using form-release agents other than polyethylene film must be sandblasted or mechanically abraded and dust free.
Pierce through the protective membrane in the front threaded section. Screw on the plastic nozzle and cut it at an angle according to the desired bead thickness and profile. Fit the cartridge into a manual or pneumatic air operated gun (provided with telescopic piston) and extrude the adhesive/sealant carefully preventing air entrapment. Once opened, packs should be used up within a relatively short time.
The optimum operating temperature for both substrate and sealant is between 15°C and 25°C.
Long term resistance to fresh water, seawater, limewater, caustic solutions and cleaning agents. Short term resistance to Petrol, grease and mineral oil. Not resistant to organic acids, concentrated mineral acids or solvents. This information is offered for general guidance only. Advice on specific applications will be given on request.
For sealing purposes:
In order to guarantee free movement of the sealant in joints, it is imperative that the sealant does not adhere to the bottom of the joint, therefore for correct joint caulking, a closed-cell polyethylene bead (joint backing rod) is to be placed at the proper depth. Apply appropriate primer to joint sides and observe the waiting time to avoid that any trapped solvent can form bubbles in the uncured sealant due to rising temperatures. Firmly extrude sealant and apply in the joint making sure that it is in full contact with the sides of the joint and with the backing rod at the bottom. Keep the nozzle in the sealant, continue on with a steady flow of sealant preceding the nozzle to avoid air entrapment. Avoid overlapping of sealant to eliminate entrapment of air. Sealant should be tooled to a smooth finish ensuring a full contact to the sides and back up material into the joint, this will also contribute in breaking the air bubbles which may be formed inside the sealant. Masking tape should be used where sharp exact joint lines or exceptionally neat lines are required. Remove the tape whilst the sealant is still soft.
For adhesive purposes:
Apply in spots or bead on the prepared surfaces then firmly press the parts which have to be bonded together.
Finishing indications and limitations.
Tooling and finishing must be carried out within the tack-free time of the sealant.
ADHESION PU40 can be over-painted. The paint must be tested for compatibility by carrying out preliminary trials. Attention must be observed with the use of alcohol or alkyd-resin since they may interfere with the curing process of the sealant and reduce the drying time of the paint itself. It should be understood that the hardness and film thickness of the paint may impair the elasticity of the sealant and lead to cracking of the paint film.
Avoid exposure to high levels of chlorine (avoid sealing joints in chlorinated swimming pools). Do not cure in the presence of curing silicone sealants. Avoid contact with alcohol and other solvent cleaners during cure. Do not apply when a moisture or vapour transmission condition exists from the substrate as this can cause bubbling within the sealant. When applying sealant, avoid air-entrapment. Since system is moisture-cured, permit sufficient exposure to air. Bonded elements may require additional holding or support during curing period.
Cleaning of equipment:
Clean tools with acetone or alcohol immediately after use. Cured material can only be removed mechanically.
Personal protective measures:
Keep out of reach of children. If skin contact occurs, remove immediately and wash with soap and water.
ADHESION PU40 can be stored for 12 months in its original packaging (unopened container) at 10°- 25°C in a cool, dry place. The storage temperature should not exceed 25°C for extended periods of time. Keep away from wet areas, direct sunlight and heat sources.
Alu-cartridge 310ml: 12 cartridges per box
Alu-PE bags 600 ml: 20 bags per box
Alu-PE bags 1800 ml: 6 bags per box (on request)
Technical certificate suitability of materials and products for use in construction TC 05.13.61.16 from 02.09.2016
Certified ISO 11600 F25 HM «Classification and requirements for high-modulus sealants in the construction"
According to DIN 18540, ASTM 920, DIN 11431, ASTM 793-91, BS 6920.
ADHESION PU40 is a multipurpose, high performance, sealant and elastic adhesive. Bonds well to a wide variety of substrates and enables permanent elastic sealing with high adhesive strength. Suitable substrates are: concrete, wood, metal, painted surfaces and plastics. Over-paintable.
• Permanently flexible
• Short cut-off string
• Stable – No shrinkage
• Bonds and seals at the same time
• Adhesion to a wide range of substrates
• Replaces rivets and mechanical fasteners
• Non-sag consistency - Good thixotropy
• Allows equalised stress transfer due to permanent elasticity.
• Vibration and sound dampening properties
• Excellent resistance to ageing, weathering – suitable for indoor and outdoor use
• Over-paintable with many water/solvent based paints (preliminary tests recommended)
Appearance - Thixotropic paste
Colour - White, Grey, Black. Others on request.
Chemical nature - Polyurethane
Curing Mechanism - Moisture-curing
Curing through volume (1 day at 23°C and 50% r.h.) [mm] 2,0 – 3,0
Non-sag properties - good
Shore A (23°C and 50% r.h.; DIN 53505) 35-45
Density (23°C and 50% r.h.) [g/cc]
Colour black: 1,31 ± 0,02
Colour grey: 1,33 ± 0,02
Colour white: 1,35 ± 0,02
Tack-free time (23°C and 50% r.h.) [min] 45-75
Elastic modulus at 100% (ISO 37 DIN 53504) [N/mm2] ≥ 0,8
Tensile strength (ISO 37 DIN 53504) [N/mm2] ≥ 1,8
Elongation (ISO 37 DIN 53504) [%] ≥ 450
Application temperature [°C] from +5 to +40
Temperature Resistance [°C] -40...+90, for short period up to 120